- CNC USB CONTROLLER MANUAL HOW TO
- CNC USB CONTROLLER MANUAL INSTALL
- CNC USB CONTROLLER MANUAL SOFTWARE
Trapezoidal screw pitch is generally 4MM, axis number of steps to be set to 400. 4.3 Axis setting 1 Pulses / stepĢ2 Set the number of pulses per unit, this value is very important, please use the basic settings after setting the calibration function tests.
Pause dialog Pause pop-up dialog Pause deceleration Pause is enabled when decelerating, the proposed hook, avoid high-speed movement will be suspended inertial motion. Set this too low will cause the machine to shake, if set too big, the detail will be lost too. Program will attempt to delete the lines shorter than the specified length. Optimization thresholds Optimize the degree of optimization of the threshold setting. If the angle between the two movements is less than this value will reduce the walking speed. Usuall positioning tool as belows:ġ5 Status bar Left side display control card cache information Right side picture shows in controlling status When processing, it will shows the working condition File menuĢ1 Advance angle used to calculate the speed, if the angle between the two movements is bigger than this value will not reduce speed.
CNC USB CONTROLLER MANUAL SOFTWARE
Orange Box - device processing capacity range Gray grid - machine worktable Axis arrow - display coordinate system origin Red axis - the origin of the coordinate system selected White Lines - machining feed path Green Line blank path Red lines - selected path (on the right Select G-code line number) Yellow Cone - the current tool position Orange cones - analog display position Dark green / gray cone - G28 and G30 Location Dark green / gray - project scope and procedures for cutting range Shortcuts: Zoom / shrink: mouse wheel Shift: Press the left mouse button and move 3D perspective changes: Press the right mouse button and move Manually G code input window G code text can be entered: Devices such as input G1 X123 F234 F-way speed of X axis will be moving forward 123 units.ġ4 Toolbar Toolbar functions from left to right: Emergency Stop Open the code file Begin Stop Pause Top View Lateral view Front View 3D perspective Zoom Shrink Centered at the origin Show all If software shows status below, it says the controller card comminication faile, or you pressed the emergnecy button.
CNC USB CONTROLLER MANUAL INSTALL
Four-axis controller card instrudtion: 2.3 Support 4 th axis machine Can switch 3 modes: Normal XYZ, thermal cutting XYUV, rotating XYZA, Provided for each axis 25 khz pulse signal 12 us minimum pulse width All axis limit Can be accessed by external port, such as hand remote controller 3 digital outputs (spindle / cutting liquid / mist) 3.Software 3.1 Installation System need to insall: - DirectX 9c for.net - Microsoft.NET 3.5 SP1 Framework - Controll software Install driver First install - NET35ġ3 This window displays the device, tools, machining path 3D map. Load DXF file Load directly PLT/HPGL file Load directly picture file Load directly drill file Load directly GERBER file Advanced tool change function export G-code export DXF export CSV export NCĥ 2.2 One point of USB card connect controller box by parallel port Another point connect computer USB port.
CNC USB CONTROLLER MANUAL HOW TO
3 How to connect: USB 25 pins functions: Function DB25pins Remark X axis (step pin) 2 Xaxis (dir pin) 3 Y axis (step pin) 4Ĥ Y axis (dir pin) 5 Z axis(step pin) 6 Zaxis (dir pin) 7 A axis (step pin) 8 A axis(dir pin) 9 External input interface (optoelectronic isolation) IN10 10 External emergency button IN11 11 X axis limit switch IN12 12 Y axis limit switch IN13 13 Z axis limit switch X Y Z A axis Enabled 14 Enable IN15 15 Tool setting* No usage of other pins * this function is choosable, if there was, drive board will available Spec&functions 2.1 Run Windows XP, Vista or Windows 7 (32 bit or 64bit) with USB2.0 Andvanced Interpolation algorithm High-performance IO buffer Provide, Start, Stop, Pause, Continue Support standard RS274/NGC G-code (EMC2 compatible) Support anvanced G-codes - G40, G41, G42 (tool radius compensation) Support anvanced G-codes - G43, G49 (Tool length encoding) Support anvanced G-codes - G54, G59.3 (coordinate system) support SolidCAM, MasterCAM, ArtCAM, Vectric.